The STIHL TS350 is a professional-grade cut-off saw designed for heavy-duty concrete, asphalt, and masonry cutting. This parts manual provides detailed information on all components, assemblies, and replacement parts for the TS350 model. Below are key sections for identification, major assemblies, individual parts, ordering information, and maintenance.
Key identifiers: Model TS350, Serial number location (on crankcase), Engine type, Displacement, Power output.
| Feature | Description |
|---|---|
| Model | TS350 Professional Cut-Off Saw |
| Engine Type | 2-stroke, single cylinder, air-cooled |
| Displacement | 64.1 cm³ (3.91 cu. in.) |
| Power Output | 3.0 kW (4.1 hp) |
| Fuel/Oil Mix | 50:1 (STIHL HP Ultra oil) |
| Cutting Wheel Diameter | 300 mm (12 inches) max |
| Weight (without wheel) | Approx. 9.5 kg (20.9 lbs) |
| Ignition System | Electronic, capacitor discharge |
| Carburetor | Diaphragm type with fuel pump |
| Starter | Rewind starter with decompression valve |
Exploded views and part numbers for main saw groups.
WARNING! Disconnect spark plug before disassembly. Use genuine STIHL parts for safety and performance.
Detailed parts list for engine internal components.
CAUTION! Engine components must be installed with proper torque specifications.
Parts for operator controls and handles.
Front Handle: Part number 0000 141 2011 with anti-vibration mounts (0000 141 2012). Rear Handle: Part number 0000 141 2013 with throttle trigger (0000 141 2014), throttle cable (0000 141 2015), and throttle lock (0000 141 2016). Master Control Lever: Part number 0000 141 2017 for choke/stop functions. Handle Mounting Bolts: M6 x 20mm, part number 0000 141 2018.
Components for fuel delivery and air filtration.
Tip: Replace fuel lines annually; clean air filter regularly.
Parts for spark generation and stopping.
WARNING! Always disconnect spark plug wire during maintenance.
Transmission and clutch components.
| Part | Part Number | Description |
|---|---|---|
| Clutch Drum | 0000 141 2035 | Centrifugal clutch assembly |
| Clutch Shoes | 0000 141 2036 | Set of 3 shoes with springs |
| Needle Bearing | 0000 141 2037 | For clutch drum |
| Drive Shaft | 0000 141 2038 | From crankshaft to clutch |
| Oil Seals | 0000 141 2039 | Set for crankcase |
| Gaskets | 0000 141 2040 | Crankcase gasket set |
Bolts, nuts, washers, and clips.
Engine Mounting Bolts: M8 x 35mm, part number 0000 141 2041. Handle Mounting Screws: M6 x 20mm, part number 0000 141 2042. Guard Screws: M8 x 25mm, part number 0000 141 2043. Flange Nut: M14 x 1.5mm, part number 0000 141 2044. Circlips: For piston pin, part number 0000 141 2045. Washers: Flat and lock washers kit, part number 0000 141 2046.
Use STIHL part numbers when ordering. Most parts are specific to TS350; some interchange with TS400, TS420. Check serial number for exact compatibility.
CAUTION! Non-genuine parts may void warranty and cause unsafe operation.
| Component | Interval | Action |
|---|---|---|
| Air Filter | Daily/10 hours | Clean; replace if damaged |
| Spark Plug | 100 hours | Clean gap; replace if worn |
| Fuel Filter | 100 hours | Replace in-tank filter |
| Cutting Guard | Inspect daily | Replace if cracked |
| Clutch Shoes | 300 hours | Inspect wear; replace set |
| Crankcase Seals | 500 hours | Inspect for leaks; replace if needed |
| Anti-Vibration Elements | 200 hours | Inspect; replace if hardened/cracked |
Reset: N/A for parts manual.
Service: Authorized STIHL dealers only. Contact 1-800-467-8445 or www.stihlusa.com.