STIHL FS 56 Parts Manual

The STIHL FS 56 is a lightweight, professional-grade trimmer designed for demanding clearing and trimming work. This manual provides detailed parts identification, exploded diagrams, and ordering information for the FS 56 C-E trimmer. It is intended for qualified servicing dealers and technicians to ensure proper maintenance, repair, and genuine STIHL parts replacement. Below are key sections for safety, parts diagrams, ordering, and specifications.

1. Safety Information 2. General Parts Diagram 3. Engine Assembly Parts 4. Fuel System Parts 5. Ignition System Parts 6. Drive Shaft & Gearhead Parts 7. Cutting Attachment Parts 8. Handle & Control Parts 9. Specifications 10. Parts Ordering Information 11. Warranty & Service

Safety Information

Before performing any maintenance or parts replacement, read the original instruction manual. Always use STIHL-approved tools and genuine STIHL parts. Disconnect the spark plug boot before working on the unit. Wear appropriate personal protective equipment (PPE).

SymbolMeaningAction
⚠️WarningIndicates a potentially hazardous situation which could result in serious injury or death.
⚙️NoteImportant information for correct procedure or part selection.
🛑CautionIndicates a potentially hazardous situation which could result in minor or moderate injury or damage to the unit.

WARNING! Never operate a unit with damaged or improperly assembled parts. Use only parts specified in this manual.

General Parts Diagram

Exploded view of the main assemblies of the STIHL FS 56.

  1. Engine Assembly (Cylinder, Piston, Crankcase)
  2. Fuel System (Tank, Cap, Filter, Lines, Carburetor)
  3. Ignition System (Spark Plug, Ignition Module, Stop Switch)
  4. Drive Shaft Assembly (Shaft, Bearings, Tubes)
  5. Gearhead Assembly (Bevel Gears, Housing, Seal)
  6. Cutting Attachment (Cutting Head, Blades, Guard)
  7. Handle & Controls (Handlebar, Throttle Trigger, Lockout)

Note: Diagrams are for reference. Always match part numbers when ordering.

Engine Assembly Parts

Parts list for the 2-stroke engine (FS 56 C-E).

Part NumberDescriptionQty
0000 400 1300Cylinder1
0000 030 2001Piston Assembly1
0000 400 1305Crankcase, complete1
0000 400 1307Crankshaft1
0000 141 1600Muffler1
0000 141 1605Spark Arrestor Screen1
0000 141 1610Muffler Cover1

CAUTION! Ensure all gaskets and seals are replaced during reassembly to prevent air leaks.

Fuel System Parts

Tip: Always use fresh, properly mixed fuel (50:1 STIHL HP Ultra oil with gasoline).

Ignition System Parts

Components for starting and stopping the engine.

Part NumberDescription
0000 400 1800Ignition Module (Electronic)
0000 400 1805Spark Plug (Bosch WSR 6 F)
0000 400 1810Spark Plug Boot
0000 400 1815Stop Switch Assembly
0000 400 1820Rewind Starter Assembly
0000 400 1825Starter Rope
0000 400 1830Starter Pulley

WARNING! Always disconnect the spark plug boot before servicing the ignition system.

Drive Shaft & Gearhead Parts

Parts for transmitting power from the engine to the cutting head.

  1. Drive Shaft: Part # 0000 350 3001 (Flexible)
  2. Drive Tube: Part # 0000 350 3005
  3. Bearing (Upper): Part # 0000 350 3010
  4. Bearing (Lower): Part # 0000 350 3015
  5. Gearhead Housing: Part # 0000 350 3100
  6. Bevel Gear Set: Part # 0000 350 3105
  7. Output Shaft: Part # 0000 350 3110
  8. Seal Kit: Part # 0000 350 3115

Note: Lubricate the gearhead with STIHL Gear Oil (Part # 0000 350 3120) after assembly.

Cutting Attachment Parts

Parts for the cutting head, blades, and guard.

Part NumberDescriptionApplication
0000 350 4001PolyCut Head 25-2For nylon line cutting
0000 350 4005Cutting Line (0.095" spool)Replacement line
0000 350 4010Circular Grass BladeFor heavy grass/weeds
0000 350 4015Metal Blade (4-tooth)For tough brush/saplings
0000 350 4020Blade Bolt & Washer SetFor securing blades
0000 350 4025Deflector/GuardSafety guard
0000 350 4030Bearing for Cutting HeadReplacement bearing

CAUTION! Always ensure the cutting attachment is correctly installed and the guard is in place before operation.

Handle & Control Parts

Parts related to operator controls and ergonomics.

Tip: Check throttle cable adjustment and trigger operation for smooth control.

Specifications

Technical data for the STIHL FS 56.

SpecificationDetail
Engine TypeSTIHL 2-MIX single-cylinder, 2-stroke
Displacement27.2 cm³ (1.66 cu. in.)
Power Output0.9 kW (1.2 bhp)
Fuel/Oil Ratio50:1 (STIHL HP Ultra)
Idle Speed2,800 rpm
Max. Engine Speed12,500 rpm
DriveFlexible shaft
Gearhead Ratio1.27:1
Cutting Attachment SpeedApprox. 9,800 rpm
Sound Pressure Level96 dB(A)
Vibration Level (Handle)4.5 m/s²
Weight (without cutting attachment)5.0 kg (11.0 lbs)

Parts Ordering Information

Always order parts by the correct part number. Contact an authorized STIHL servicing dealer.

  1. Identify the part needed using the diagrams and part numbers in this manual.
  2. Provide the unit's serial number (located on the crankcase) to your dealer.
  3. Specify the exact part number and description.
  4. Use only genuine STIHL parts to maintain performance, safety, and warranty.

WARNING! The use of non-STIHL parts may void the warranty and can lead to unsafe operation or unit damage.

Warranty & Service

STIHL Limited Warranty applies when unit is purchased from an authorized STIHL dealer and serviced with genuine STIHL parts. For service, locate your nearest authorized STIHL dealer.

IssueResourceContact
Parts IdentificationThis manual, STIHL IPL (Interactive Parts List)Your STIHL Dealer
Technical ServiceAuthorized STIHL Service CenterFind dealer at www.stihlusa.com
Warranty ClaimsOriginal proof of purchase requiredThrough purchasing dealer
Safety & Operation ManualsSTIHL websitewww.stihlusa.com/manuals

Reset: For engine issues, refer to troubleshooting in the instruction manual.

Service: 1-800-467-8445 (STIHL USA); www.stihlusa.com

STIHL FS 56 Parts Manual © - All Rights Reserved 2025. STIHL is a registered trademark of Andreas Stihl AG & Co. KG.