Stihl FS 130 Parts Manual

The Stihl FS 130 is a professional-grade straight-shaft trimmer designed for demanding clearing and trimming applications. This parts manual provides detailed diagrams, part numbers, and ordering information for all components of the FS 130 trimmer, including the engine, cutting head, drive shaft, handle assembly, and fuel system. Below are key sections for identification, engine parts, cutting attachments, drive train, controls, and maintenance parts.

Identification & Specifications

Key identifiers: Model FS 130, Engine type (2-stroke), Displacement, Power output, Weight, Shaft type (straight).

Engine Assembly Parts

Cylinder, piston, crankshaft, bearings, seals, and crankcase components.

1. Cylinder: Includes cylinder, cylinder head, and mounting studs.
2. Piston Assembly: Piston, piston rings, wrist pin, and circlips.
3. Crankshaft: Main crankshaft with integrated counterweights.
4. Crankcase: Upper and lower halves, gaskets, and screws.
5. Bearings & Seals: Main bearings, crankshaft seals, and O-rings.

WARNING! Engine disassembly requires specialized tools and knowledge. Refer to service manual for procedures.

Cutting Attachment Parts

Parts for trimmer heads, blades, and mounting hardware.

1. Trimmer Head: AutoCut C 5-2 head or compatible, including spool, spring, and cover.
2. Blade Adapter: For mounting circular saw blades or grass knives.
3. Blade Bolts & Nuts: Securing hardware for cutting attachments.
4. Deflector & Shield: Debris shield and cutting attachment guard.
5. Retaining Screws: For securing the attachment to the gearhead.

CAUTION! Always use the correct guard for the cutting attachment. Ensure all hardware is tightened to specification.

Drive Shaft & Gearhead Parts

• Drive Shaft: Solid steel shaft with coupling at engine and gearhead ends.
• Gearhead Housing: Aluminum housing containing bevel gears.
• Bevel Gears: Upper and lower gears for 90° power transfer.
• Bearings & Seals: Gearhead bearings, oil seals, and gaskets.
• Output Shaft: Shaft that drives the cutting attachment.
• Lubricant: STIHL gear grease for gearhead maintenance.

Handle & Control Parts

Handle assembly, throttle trigger, lockout, and control cables.

Handle: D-shaped or loop handle, vibration dampeners, mounting clamps.

Throttle Control: Throttle trigger, throttle cable, lockout lever, and return spring. Stop Switch: Kill switch, wiring, and mounting. Shaft Clamp: Clamp securing handle to shaft. Harness Attachment Points: D-rings or hooks for shoulder harness.

Fuel System Parts

Fuel tank, carburetor, fuel lines, filter, and primer bulb.

1. Fuel Tank: Polyethylene tank with cap and vent.
2. Carburetor: Zama or Walbro diaphragm carburetor with adjustment screws.
3. Fuel Lines: Supply and return lines, impulse line.
4. Fuel Filter: In-tank sintered bronze or felt filter.
5. Primer Bulb: For easy starting.

Tip: Use only clean, fresh fuel mix. Inspect fuel lines regularly for cracks.

Ignition System Parts

Ignition module, spark plug, stop switch, and wiring.

1. Ignition Module (CDI): Controls spark timing.
2. Spark Plug: Bosch or NGK, specific heat range.
3. Spark Plug Boot: Insulated boot and terminal nut.
4. Stop Switch Wire: Connects kill switch to ignition module.
5. Flywheel & Magneto: Flywheel with magnets, ignition coil air gap.

WARNING! Disconnect spark plug boot before performing any maintenance.

Air Filter & Cooling Parts

Air filter cover, filter element, pre-cleaner, and cooling fins.

Starter Assembly Parts

Starter housing, rope, pulley, spring, and pawls.

CAUTION! Starter spring is under tension. Use proper safety procedures when servicing.

Muffler & Exhaust Parts

Muffler body, spark arrestor screen, gasket, and mounting bolts.

Ordering & Exploded Views

Ordering: Use the 10-digit STIHL part number from the diagrams. Contact an authorized STIHL dealer.

Support: For technical assistance, contact STIHL at 1-800-467-8445 or visit www.stihlusa.com.